Pendu Used Equipment

#1582 Model 4700 Stacker

PENDU 4700 STACKER

PLC controlled with touch screen and ewon modem
Layers per minute:
Up to 25 layers per minute
Material capacity:
3/8″ To 2″ thick
2″ To 6″ wide
28″ Inches to 72 inches long
Pit-unscrambler:
60 Degree incline
2060 chain with lugs
2 HP VFD electric drive
Accumulating chain:
Strands move with stacker strands
Each strand with fixed driven even-ending belt
Two 1 HP VFD electric drives
Tie strip placer:
Two adjustable automatic stick magazines with programable placements
Stacker:
Two 1 HP VFD electric drives
Manual adjustable width
Air cylinder escapement
Top hold down:
Automatically actuated by air cylinder
Applies down pressure during the layer escapement cycle
Stack lowering:
Automatic Lowering
Scissors lift
Hydraulic pump with 7.5 HP electric motor
Takeaway rollers:
15 foot long gravity section of takeaway rollers
Driven roller for gravity rolls
(1) Driven roller with vulcanized rubber
(1) 1/2 HP electric drive
Chain driven
Air requirements:
80 PSI, 3 CFM

#1581 AUXILIARY HYDRAULIC POWER UNIT

1030 AUXILIARY HYDRAULIC POWER UNIT

Closed center pressure compensated
30 Gallon per minute pump
30 HP Electric motor
60 Gallon tank
60 Gallon of multi viscosity oil
Thermostat, heater & cooler – requires 220V/1PH/60HZ
1 1/4” Connecting hose kit
Check valve
Dump valve

ITEM 15957-4

LUMBER TRANSFER DECK WITH BOARD DEALER
WH 78 chain transfer deck for single layers of lumber
8 Foot long (4) strand deck includes:
1-15/16” Diameter head shaft assembly with bearings and sprockets
1-15/16” Diameter individual stub tail shaft assembly with sprockets and take ups
All welded structural steel construction
UHMW wear strips in the chain ways
Steel cross sills and legs for top of chain height of 54”
2 HP Electric drive
BOARD DEALER WHEEL ASSEMBLY
Manually adjustable dead stops for material width.
Automatic hydraulic actuated material lifter.
Automatic board dealer with serrated wheel assembly

#1495 – PENDU LUMBER TRANSFER DECK C55 B Rooftop Chain Transfer Deck For Single Layers of Boards and Cants

18’10” long (2) strand deck includes:

• 1 15/16″ diameter head assy with bearings and sprockets
• 1 15/16″ diameter individual stub tail shaft assy with sprockets
  and take-ups
• 36″ min. to 54″ max. material length
• All welded structural steel construction
• Wear strips in the chainways, chain return races
• Steel cross sills and legs
• Steel landing table 2 strands 4 foot long
• Shear bar

VERTICAL DRILL STATION, PENDU MODEL 1400

• 16′ long with powered rollcase
• 14 inch wide rolls
• Machined roll centers: 12″ fixed
• Working height: 48″
• Minimum material length: 30″
• Console controlled
• Minimum drill center line from end of log: 3 3/4″
• Minimum drill center line between two units: 7 1/2″
• 32 drill units: 16 top, 16 bottom
• 12″ fixed heads
• Hydraulic positioning of drill heads
• Bottom waste removal auger

#1496 – 10 FEET OF CANTILEVERED ROLLCASE

• Machined rolls: 5″ wide, 4.5″ diameter, 15″ roll centers
• Hydraulic drive
• 36″ min. to 54″ max. material length
• 1 15/16″ roller arbors
• Pillow block bearings
• Steel rails & legs
• 2 top pinch roll: Urethane coated drive roll, air cylinder actuated,
  electric eye activated, driven from rolltrack

#1498 – PENDU LUMBER TRANSFER DECK

• 26 foot long 2 strand deck
• 1 15/16″ diameter head shaft assy with bearings and sprockets
• 1 15/16″ diameter individual stub tail shaft assy with sprockets and take-ups
• 36″ min to 54″ max material length
• All welded structural steel construction
• Wear strips in the chainways, chain return races
• Steel cross sills and legs
• Steel landing table 2 strand 2 foot long
• 1 HP 3 PH TEFC electric Vfd

#1120 – WEST PLAINS CONTROL PANEL

• One 2, 3, 10, and 30 HP starters
• One 150 HP Y-delta starters
• 10 push buttons
• Transformer
• Subpanel
• Square D breaker handle
• Square D breaker
• Set up for 586 Morbark chipper