Pendu Used Equipment

All Pendu used equipment is sold completely refurbished and ready to install. Each item undergoes a rigorous and thorough rebuilding process. You can purchase Pendu used equipment with complete confidence that it will perform up to your expectations.

Call 800-233-0471 for Additional Information

#1582 Model 4700 Stacker

PENDU 4700 STACKER

PLC controlled with touch screen and ewon modem
Layers per minute:
Up to 25 layers per minute
Material capacity:
3/8″ To 2″ thick
2″ To 6″ wide
28″ Inches to 72 inches long
Pit-unscrambler:
60 Degree incline
2060 chain with lugs
2 HP VFD electric drive
Accumulating chain:
Strands move with stacker strands
Each strand with fixed driven even-ending belt
Two 1 HP VFD electric drives
Tie strip placer:
Two adjustable automatic stick magazines with programable placements
Stacker:
Two 1 HP VFD electric drives
Manual adjustable width
Air cylinder escapement
Top hold down:
Automatically actuated by air cylinder
Applies down pressure during the layer escapement cycle
Stack lowering:
Automatic Lowering
Scissors lift
Hydraulic pump with 7.5 HP electric motor
Takeaway rollers:
15 foot long gravity section of takeaway rollers
Driven roller for gravity rolls
(1) Driven roller with vulcanized rubber
(1) 1/2 HP electric drive
Chain driven
Air requirements:
80 PSI, 3 CFM

#1495 – PENDU LUMBER TRANSFER DECK C55 B Rooftop Chain Transfer Deck For Single Layers of Boards and Cants

#1495 – PENDU LUMBER TRANSFER DECK C55 B Rooftop Chain Transfer Deck For Single Layers of Boards and Cants

18’10” long (2) strand deck includes:

  • 1 15/16″ diameter head assy with bearings and sprockets
  • 1 15/16″ diameter individual stub tail shaft assy with sprockets
    and take-ups
  • 36″ min. to 54″ max. material length
  • All welded structural steel construction
  • Wear strips in the chainways, chain return races
  • Steel cross sills and legs
  • Steel landing table 2 strands 4 foot long
  • Shear bar
VERTICAL DRILL STATION, PENDU MODEL 1400

VERTICAL DRILL STATION, PENDU MODEL 1400

  • 16′ long with powered rollcase
  • 14 inch wide rolls
  • Machined roll centers: 12″ fixed
  • Working height: 48″
  • Minimum material length: 30″
  • Console controlled
  • Minimum drill center line from end of log: 3 3/4″
  • Minimum drill center line between two units: 7 1/2″
  • 32 drill units: 16 top, 16 bottom
  • 12″ fixed heads
  • Hydraulic positioning of drill heads
  • Bottom waste removal auger
#1496 – 10 FEET OF CANTILEVERED ROLLCASE

#1496 – 10 FEET OF CANTILEVERED ROLLCASE

  • Machined rolls: 5″ wide, 4.5″ diameter, 15″ roll centers
  • Hydraulic drive
  • 36″ min. to 54″ max. material length
  • 1 15/16″ roller arbors
  • Pillow block bearings
  • Steel rails & legs
  • 2 top pinch roll: Urethane coated drive roll, air cylinder actuated,
    electric eye activated, driven from rolltrack
#1498 – PENDU LUMBER TRANSFER DECK

#1498 – PENDU LUMBER TRANSFER DECK

  • 26 foot long 2 strand deck
  • 1 15/16″ diameter head shaft assy with bearings and sprockets
  • 1 15/16″ diameter individual stub tail shaft assy with sprockets and take-ups
  • 36″ min to 54″ max material length
  • All welded structural steel construction
  • Wear strips in the chainways, chain return races
  • Steel cross sills and legs
  • Steel landing table 2 strand 2 foot long
  • 1 HP 3 PH TEFC electric Vfd
#1120 – WEST PLAINS CONTROL PANEL

#1120 – WEST PLAINS CONTROL PANEL

  • One 2, 3, 10, and 30 HP starters
  • One 150 HP Y-delta starters
  • 10 push buttons
  • Transformer
  • Subpanel
  • Square D breaker handle
  • Square D breaker
  • Set up for 586 Morbark chipper